TULA.VN - Electronics Materials and Instruments in Vietnam  
       ENGLISH     
Trang chủ | Đối tác | Thư ngỏ | Sơ đồ web | Liên hệ
            
MÁY NẠP Jig test | THIẾT BỊ công cụ | VẬT TƯ hoá chất | LINH KIỆN phụ kiện | DỊCH VỤ GIỚI THIỆU | HỖ TRỢ
 SẢN PHẨM
 Máy nạp rom, Jig test
» Máy nạp rom đa năng
» Máy nạp Gang đa năng
» Máy nạp rom on-board
» Máy nạp chuyên biệt
» Hệ thống nạp tự động
» Phụ kiện đế nạp socket
»Xoá Rom, kiểm tra IC
» Sao chép ổ cứng, thẻ nhớ
»Jig test ICT/FCT/DIP-pallet
 Đo lường và kiểm tra
» Dao động ký oscilloscope
» Thiết bị viễn thông, RF
» Bộ thu thập dữ liệu
» Đồng hồ vạn năng số
» Máy phát xung, đếm tần
» Máy đo LCR, linh kiện
» Bộ đổi nguồn, tải điện tử
» Kit đào tạo, thực hành
 Các công cụ sản xuất
» Máy khò, mỏ hàn thiếc
» Tủ sấy, tủ môi trường
» Dây chuyền SMT Line
» Thiết bị sản xuất PCBA
 Thiết bị, công cụ khác
» Thiết bị Automotive
» Đo lực, cơ điện khác
» Thiết bị quang học
 Linh phụ kiện Điện tử
» Vi điều khiển họ 8051
» Nuvoton ARM Cortex-M
» Nuvoton ARM7/9 Soc
» Chip phát nhạc, audio
» Wireless RF IC, Tools
» Vật tư hàn, rửa mạch
 e-Shop thiết bị, vật tư
 Số lượt truy cập

237191680
lượt xem, tính từ 20/12/2006
 Ai đang online
Hiện tại có 0 khách và 0 thành viên đang online.

Bạn là khách. Bạn có thể đăng kí bằng cách nhấn vào đây



OUR PARTNERS
(Products Line-Card)



Flash Support Group

PEmicro

Power Supply

Shenzhen KESD Technology Co.,Ltd.



Car and Consumer IC Solutions Provider


  

Danh mục nội dung: Chuyên mục chính/4. Công cụ và thiết bị điện tử chuyên dùng khác/4.3. Thiết bị đo cơ, lực và đo kiểm bằng hình ảnh


      
   USB Power Delivery Tester
  Part#: PassMark Software USB Power
  Ghi chú: Bộ kiểm tra phân phối điện qua USB
  Nhãn hiệu: PassMark Software (Mỹ/USA)
  [ Tài liệu Datasheet ]   [ Báo giá Quotation sheet ]   [ Shopping Shopping now ]   [ Views: 4047 ]   2021-03-30
 ◊ Đặc điểm chính:
For troubleshooting USB ports and USB chargers
  • Test the power delivery capability of USB ports, USB chargers, and USB power banks.
  • Check if a USB host is capable of delivering its maximum specified wattage without failing.
  • Detect the wattage a USB charger (wall-wart) claims to support, which in turn controls the charging speed of mobile phones and other USB connected battery devices.
  • Check that voltage levels remain within specification under high load.
  • Measure the exact power usage of USB devices.
  • Use it with the USB 3.0 Loopback Plug, to test communication speed, data integrity, and power delivery of USB ports simultaneously.
  • QC4+ and PPS support available in model PM125.

Safety Precautions

Do not touch or cover heatsink during operation as it can reach high temperatures, which could result in burns or failure of the USB PD Tester.

Do not block the operation of the fans & allow good airflow. Allow at least 10cm of air gap around the back of the fans. Also ensure there is airflow under the device.

Only use the USB PD tester with devices that claim compliance with the USB standards. A catastrophic failure of the device under test can result in the shorting of mains power to the USB cable. Which can both destroy the USB PD Tester and present a serious electrocution hazard.

The USB PD Tester is not a consumer device. It was designed for use by qualified electrical engineers.

Safety Precautions

Always have someone monitor the testing in case the device under test suddenly fails. Do not start a test and walk away.

Some USB power supplies are known to not fully comply with the USB standards. Some also do not comply with relevant electrical standards in the countries where they are sold. Faulty or poorly designed devices can be dangerous! The USB PD Tester may expose design and manufacturing flaws in the device when putting the device under high load. The result can be catastrophic failure of the device under test. Which in turn can lead to fire, melting of the device under test, smoke, electrical shorts and even destruction of the USB PD tester itself.

Do not draw more current from the device than it claims to support. The port might be damaged as a result, or over current protection might lead to the port shutting down.


Video:




CÁC SẢN PHẨM KHÁC CÙNG NHÀ SẢN XUẤT / OTHER PRODUCTS FROM PassMark Software
Inline PSU Tester
USB 2.0 Loopback Plugs
PCIe Test Cards
USB Power Delivery Tester
USB 3.0 Loopback Plugs
PC Test Kit



Thao tác người sử dụng: [ Thêm dữ liệu ]

 





ĐIỀU KHOẢN SỬ DỤNG

Công ty TNHH Giải pháp TULA - TULA Solution Co., Ltd
VPGD: Số 6 Ngõ 23 Đình Thôn (Phạm Hùng), Mỹ Đình, Nam Từ Liêm, Hà Nội
Tel.: 024.39655633,  Hotline: 0912612693,  E-mail: 

 
Bản quyền © 2005-2023, Công ty TNHH Giải pháp TULA sở hữuGIỚI THIỆU | HỖ TRỢ